Description
Aqara Motion Sensor P1 detects body motion and the state of ambient light. If there are any people moving or any change in the ambient light state in the areas under detection, the motion sensor will send notice to the Aqara Home app through the connected Aqara Zigbee 3.0 Hub or link to other devices.
MAIN FEATURES:
Configurable detection timeout
5-year battery life*
All-round compatibility
170 field of view
Adjustable sensitivity (distance)
Built-in light sensor
Smart home automations
Local and remote alarm
Zigbee 3.0 protocol
Future-proofing via ota
5-year battery life can be achieved with the LED indication function turned off and with detection timeout not less than 30 seconds.
** Aqara Zigbee 3.0 hub and controllers are required for this functionality.
SPECIFICATIONS:
Model: MS-S02
Battery: CR2450
Wireless Protocols: Zigbee 3.0
Dimensions: 33.1 33.1 41.6 mm
Operating Temperature: -10 C to 55 C
Operating Humidity: 0 to 95%RH, no condensation
Zigbee Operation Frequency: 2405-2480 MHz
Zigbee Maximum Output Power ? 13 dBm
App: Apple Home app (iOS 10.3 or later), Aqara Home app (Android 5.0 or later, iOS 10.3 or later)
Regulatory Certification: ICASA
– Apple HomeKit compatible accessories:
Aqara Hubs
Aqara Wireless Mini Switch,
Aqara Wireless Remote Switch (Single Rocker),
Aqara Wireless Remote Switch (Double Rocker),
Aqara Wireless Remote Switch H1 (Single & Double Rocker),
Aqara Door and Window Sensor,
Aqara Temperature and Humidity Sensor,
Aqara Vibration Sensor,
Aqara Water Leak Sensor,
Aqara TVOC Air Quality Monitor,
Aqara LED Light Bulb (Tuneable White),
Aqara Single Switch Module T1 (With Neutral),
Aqara Single Switch Module T1 (With Neutral),
Aqara Smart Wall Switch H1 (No Neutral) (Single & Double Rocker),
Aqara Smart Wall Switch H1 (With Neutral) (Single & Double Rocker),
Aqara Smart Roller Shade Controller,
Aqara Roller Shade Driver E1,
Aqara Camera Hub G2H,
Aqara Camera Hub G3,
Newer Models.
PLEASE NOTE:
One Aqara ZigBee 3.0 Hub can connect up to 128 Aqara devices.
To control this Apple HomeKit-enabled accessory, iOS 10.3 or later is recommended.
Controlling Apple HomeKit-enabled accessory automatically and away from home requires an Apple TV with tvOS 10.2 or later or an iPad with iOS 10.3 or later or a Home Pod set up as a home hub.
INSTRUCTIONS:
Quick Setup
1.Before activating the accessory, please make sure you have the Aqara Home app downloaded and an Aqara Zigbee 3.0 hub installed.
2.Remove the insulating pull tab.
Pull the tab out from under the battery contact to the direction of the arrow to activate the product.
3.Please open the app, tap Home and then tap + in the top right corner to enter the Add Device (Accessory) page. Select Motion Sensor P1 and add it according to instructions in the Aqara Home app.
4.Please see www.aqara.com/support for additional information.
*If adding fails, please move the product closer to the hub and try again.
Installation and Usage
Please confirm that communication between the motion sensor and the Aqara Zigbee 3.0 Hub works normally, and then install and fix it in position.
Installation Instructions:
1.Please do not install on tile, glass, marble, or other smooth and easy-to-moisten objects to avoid the sticker from loosening.
2.Please do not install on the surface of a lighting tube or other high-temperature and heating objects to avoid the sticker from loosening.
3.Please do not install on the surface of wall coverings and other rough and uneven objects to avoid the sticker from loosening.
4.Please do not face it against electrical appliances and other heating sources to prevent infrared jamming from causing a false trigger.
*Recommended installation height is 1.2-2 m. The detection scope gets smaller if it is lower than 1.2 m. There will be a blind zone at the bottom of the motion sensor if it is installed higher than 2 m.
Direct Installation
1.Choose an appropriate installation position and make sure the installation surface is clean and flat.
2.Put the sticker on the bottom of the battery cover, determine the detection direction, stick it to the desired installation position, and press hard and evenly for 30 s to make sure it sticks firmly.
Installation with Holder
1.Choose an appropriate installation position and make sure installation surface is clean and flat.
2.Stick the sensor to the installation pedestal, and press hard and evenly for 30 s to make sure it sticks firmly.
3.Stick holder pedestal in the required area, and press hard and evenly for 30 s to make sure it sticks firmly. In the case of installing on a wall surface, it is recommended that the holder gap faces upward to facilitate adjusting detection direction.
Battery Replacement
1.Take off the battery cover from its gap with screw driver, and stretch the screw driver into battery compartment lever opening and take off the battery compartment.
2.Install two brand-new CR2450 button batteries into the battery compartment, with one firmly sticking the compartment top on the polar front and the other firmly sticking to the compartment bottom on the polar front.
3.Align to and install the battery compartment based on arrow directions, and then put on the battery cover.
Warnings
1.This product is not a toy, please keep children away from this product.
2.This product is designed for indoor use only. Do NOT use in humid environments or outdoors.
3.Beware of moisture, do NOT spill water or other liquids onto the product.
4.Do not place this product near a heat source.
5.Do not attempt to repair the product by yourself. All repairs should be performed by authorized personnel.
6.This product is designed only for improving the convenience of household life, and for status notifications. If the user violates the product instructions and this warning, the manufacturer is not responsible for any risks and property losses caused thereby.
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user.
CAUTION
1.Risk of explosion if the battery is replaced by an incorrect type.
2.Dispose of used batteries according to the instructions.
3.Do not ingest battery, Chemical Burn Hazard.
4.This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
5.Keep new and used batteries away from children.
6.If the battery compartment does not close securely, stop using the product and keep it away from children. 7.If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
8.Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
9.Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
10.A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
11.Disposal of a battery into fire or a hot oven,or mechanically crushing or cutting of a battery, that can result in an explosion.
12.Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
13.A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable 10 liquid or gas.
14.The equipment is only suitable for mounting at heights ?2 m.
What’s in the box
1 x Motion Sensor P1
1 x Holder,
1 x Holder
1 x User Manual
There are no reviews yet.